TeamMate Plug-in Modules E1/T1 MODULE E1/T1 circuits are full duplex with 2Mbps capacity in each direction. The E1/T1 module supports mux/demux signals over this 2Mbps circuit. Up to two interfaces per module for the connection of two E1/T1 links (2 Mbps each). Multiplexer will support up to two modules of this kind, that is, four interfaces for connection of four E1/T1 links (2 Mbps each) Multiplexer allows Drop/Insert functions among any of the four E1/T1 connected circuits. Interface: CCITT G703 Specifications Connector: RJ45 and BNC Binary speed: 2048Mbps +/- 50ppm Plot format: CCIT G704 Line code: HDB3 Impedance: 75 or 120 Ohms CONTROL MODULE Main Functions: Manages the system Work as an additional input/output synchronous data module Interfaces Asynchronous (RS-232)port for connecting a VT-100 compatible terminal to configure the TeamMate This module is also a router for a direct LAN connection to configure the TeamMate using TCP/IP protocol(Telnet). This module configures and control input/output modules. It facilitates switching between PCM buses and E1/T1 links according to the slots assigned by the user. The Multiplexer can keeps one slot of the E1/T1 link reserved for the control module in order to manage the remote multiplexer and then transmit and receive by this channel the remote control request. The control module monitors the system state and reports back to the management software. It stores system configuration information for automatic reset of previous values.   AUDIO ENCODER MODULE There are two available Encoder modules, 1 slot and 2 slot versions. Both versions support analog or digital inputs, but the 2 slot version has XLR inputs while the 1 slot version requires a cable to connect to XLR inputs. Audio Coding Options J41 384Kbps for mono signals - 15kHz frequency response J42 192Kbps for mono signals – 7.5kHz frequency response J57 for AES/EBU signal transmission ISO MPEG Layer II MODES: mono, stereo, dual and Joint Stereo Sample frequency: 16, 24, 32 and 48kHz Bit rates: 64, 128, 192, 256, 384Kbps Auxiliary data with audio working in MPEG - Up to two independent mono channels per module ISO MPEG Layer III MODES: mono, stereo, dual and Joint Stereo Sample frequency: 16, 24, 32 and 48kHz Bit rates: 64, 128, 192, 256, 384Kbps Auxiliary data with audio working in MPEG - Up to two independent mono channels per module G722 High Quality voice - 7kHz-frequency response-bit rate 64Kbps. Up to two independent channels per module. G711 Voice module, A& Mu-law, 3.4kHz frequency response. Up to two independent channels per module. Apt-X standard and enhanced MODES: mono, stereo Sample frequency: 16, 32 and 48kHz Bit rates: 64, 128, 192, 256, 320, 384 & 576Kbps. Auxiliary data with audio working in Apt-X. Converters: 24bit A/D Interfaces: 2 XLR females on 2 slot version / DB9 on 1 slot version. Selection between analog or digital inputs. DB9 for auxiliary data.     AUDIO DECODER MODULE There are two available Decoder modules, 1 slot and 2 slot versions. Both versions support analog or digital outputs, but the 2 slot version has XLR outputs while the 1 slot version requires a cable to connect to XLR outputs. Audio Decoding Options: J41 384Kbps for mono signals - 15kHz frequency response. J42 384Kbps for mono signals – 7.5kHz frequency response. J57 for AES/EBU signal reception. ISO MPEG Layer II MODES: mono, stereo, dual and Joint Stereo Sample frequency: 16, 24, 32 and 48kHz Bit rates: 64, 128, 192, 256, 384Kbps Auxiliary data with audio working in MPEG. Up to two independent mono channels per module. ISO MPEG Layer III MODES: mono, stereo, dual and Joint Stereo Sample frequency: 16, 24, 32 and 48kHz Bit rates: 64, 128, 192, 256, 384Kbps Auxiliary data with audio working in MPEG. Up to two independent mono channels per module. G722 High Quality voice , 7kHz frequency response, 64kbps bit rates. Up to two independent channels per module. G711 Voice module, A-law, 3.4kHz frequency response. Up to two independent channels per module. Apt-X standard & enhanced MODES: mono, stereo Sample frequency: 16, 32 y 48kHz Bit rates: 64, 128, 192, 256, 320, 384 & 576Kbps. Auxiliary data with audio working in Apt-X. Converters: 24bit A/D Interfaces: 2 XLR males on 2 slot version / DB9 on 1 slot version. Selection between analog or digital output on 2 slot version. Both Analog and Digital outputs active on 1 slot version. DB9 for auxiliary data.   SYNCHRONOUS DATA MODULE Allows synchronous transmission of data at Nx64Kbps. Free assignment of the number of slots. Provides two WAN V24/V35 interfaces.   POWER SUPPLY MODULES The TeamMate accepts up to two power supplies AC POWER SUPPLY MODULE DC REDUNDANT POWER SUPPLY 48V If a power supply fails, the TeamMate will change over to the spare power supply without interruption. Monitoring of status and power supply failure TeamMate Homepage