Common	TA Setup	DIFs	(Country)	Select country (TA201 and TA301)
			(Sw Type)	Select CO switch type
			(LDN)	Enter LDN (Non North-American)
			(SPID)	North America only
			(ID)	North America only
			(Lcl Chk)	TA101 only
			Reset
			I/F
			Sub addr
			LB
			(Inband)	TA 101 only
			(LLC)
		TA Cnfgs	Load	Load a stored TA configuration
			Save	Save current TA configuration
			Del entry	Delete a stored entry
			Clear all	Clear TA storage memory
		Conn Time	LCD Display	Activate LCD display
			Dspl Time	Display connect time
			Clr Time	Clear timer
			Dspl Num	Show dialed number
		Auto Ans		Set TA to auto answer
		AutoReCon		Set TA to redial when connection fails
		Redial		Set number of redial attempts
		Dial TO		Set dialing time-out
		RCProtpcol		Set TA remote control protocol
	Dig I/F	Def I/F		Define Digital Interface Module
		DTR/CON		Set state of DTR/CON
	Spd Dial	Save Crnt		Save current configuration and numbers
		View dir		View speed dial directory
		Edit dir		Edit a speed dial entry
		Add entry		Add a speed dial entry
		Del entry		Delete a speed dial entry
		Clear all		Clead directory (cannot be recovered)
	System LB	Sys LB		Toggle loop-back state
		LpBkBr		Set loop-back bit rate
	ANC Data	Fmt/L2	Enc Fmt	Set L2 ancillary data format (outbound)
			Dec Fmt	Set L2 ancillary data format (inbound)
		Fmt/L3	Enc Fmt	Set L3 ancillary data format (outbound)
			Dec Fmt	Set L3 ancillary data format (inbound)
		Asy Adata	MUX Rate	Set data rate
			DSP Rate	Set DSP rate (must be higher than data rate)
			Mux Mode	Set Mux mode
	User Profile	Load		Load user defaults
		Save		Save current configuration as user default
		Reset		Clear user defaults
	RPRmt Ctl	Set ID		Set rear panel RS485 RC port ID
		Interface		Select RS232 or RS485 remote control
		Port baud		Select rear panel RC port baud
		Protocol		Select rear panel RC protocol usage
		Echo		Select response echo
		485 mode		Select RS485 mode
	FPRmt Ctl	FP baud		Select front panel RC port baud
		FP proto		Select front panel RC protocol usage
		Echo		Select response echo
	Time Code	Dsply src		Set TC readout source
		Dsply spd		Print TC speed
		Dsply last		Display last TC received
		On/Off		Toggle TC readout
	Login	User		Log in as user, security level 4
		Sup User		Log in as super user, security level 7
		Factory		Log in as factory support, security level 9
	Logoff			Return to security level 1
	Lvl LEDs	Mode		Set level meter mode
		Message		Scroll message on LED display
		Intensity		Set LED intensity
	PLL	Ptr evnt		Print events input state
		Stop timer		Stop internal timer
		Program		Set event to action logic
		Set timer		Start internal timer
	Status	DIF State		Display DIF state
		DIF Enabl		Display DIF enable status
		LS Clear		Clear action word latched value
		LS Read		Read action word latched value
		RS Read		Primt real-time action word
	Virt Act			Define a virtual action
	Hot Key			Define a hot key function
	General	Version		Print software module version number
		Set Dflts		Reset to factory defaults
	G.722/H.221			Set compatibility with PKI telephones
	Other RS232	Usage		Set/activate other RS232 port usage
		Baud Rate		Set RS232 port baud rate
		CR timout		Set RS232 response time out
		CR cmd		Send command from RC port to far-end RS232 port
		EOM cmd		Terminated with this srting
	Buzzer	PB click		Toggle state of keypress beeper
		Buzzer		Toggle buzzer
	Fan			Toggle fan state
	Contrast			Adjust LCD display contrast
Encoder	Qstatus			Display encoder settings
	Bit rate			Set encoder bit rate
	Algorithm			Set encoder algorithm
	Algo mode			Set algorithm mode
	Line fmt			Select line format and lines to use
	Smpl rate			Select encoder sample rate
	More	General	Timing	Set timing source for encoder
			ACE	Enable/disable advanced concealment of errors
			Cal AD	Recalibrate A/D converter
			Sine Det	Toggle state of sine detector
		Audio In	Copy/Swap	Duplicate or swap audio channels
			Mono mix	Mix stereo source to mono
		ISO Hdr	Copyright	Toggle copyright bit in MPEG header
			Emphasis	Toggle emphasis bit in MPEG header
			Original	Toggle original bit in MPEG header
			Protect	Toggle protect bit in MPEG header
			Private	Toggle private bit in MPEG header
		Contacts	Set Switch	Set a simulated switch
		X-Inputs	X-Status	Display status of various extended inputs
			Enable	Enable various extended inputs
			Invert	Invers various extended inputs
		Psycho	Set Parm	Set psychoacoustic parameter
			Reset	Load all default parameters
			Tbl Num	Get number of default table
			Load Tbl	Load table from flash memory
			Store Tbl	Store (modified) table in flash memory
			Assign Tbl	Assign a table to use
Decoder	Qstatus			Display decoder settings
	Indep			Sets encoder/decoder interaction
	Line fmt			Selects decoder line format and lines
	Bit rate			Select decoder bit rate
	AES	TimingSrc		Select AES/EBU timing
		Output SR		Select AES/EBU sample rate
		Sync		Select AES/EBU sync source
	More	Audio out	Mute	Mute decoder
			Copy/Swap	Duplicate or swap audio channels
		Algo Mode		Set decoding mode
		ACE		Enable/disable advanced concealment of errors
		Cal DA		Recalibrate D/A converter
		Algorithm		Select decoding algorithm
		Stat bits		Display real-time status of header bits
Maint	Quiet Det	Time left		Display quiet detector time left
		Set lvl		Set quiet detector level
		Set time		Set quied detector duration
		Read lvl		Read quiet detector level
	Peak Det	Peak lev		Display peak audio level
	BER Det	Dsply cnt		Display BER test count
		Reset cnt		Reset BER counter
		Set thresh		Set BER event threshold
		Set Peak		Set BER counter maximum
		Up Cnt		Set up count level
		Down Cnt		Set down count level
	OOF Det	Dsply cnt		Display OOF test count
		Reset cnt		Reset OOF counter
		Set thresh		Set OOF event threshold
		Set Peak		Set OOF counter maximum
		Up Cnt		Set up count level
		Down Cnt		Set down count level
	Hrdw Tests	EnDis Tst		Enable hardware testing
		Hrdwr Tst		Perform hardware testing
	Security	User pwd		Changer user password
		SUser pwd		Change super user password
		Lock Out		Set access to Prima
	Status	Ver Num		Display version number of software module
	Soft Dld	Boot ROM		Boot from ROM
		FE BROM		Boot the far-end Prima from ROM
		RPRC Src		Set rear panel RC source
		RmtBt Enb		Enable remote boot
		BBM Sync		Synchronize RAM and BBM
	Debug	Wtch Prt		Set watch port