CDQPrima Support

Resetting Internal Terminal Adaptor

CDQPrima software version 27/6.27 and earlier, TA101 only:

1. From the CDQPrima's Front Panel, select [Common] using the arrow keys and press "Enter."
2. Select [TA Setup] and press "Enter."
3. Using the arrow keys, select [Reset] and press "Enter." 
4. For 100 Series Prima codecs, select [DIF12] and Press "Enter" 
5. For 200 Series Prima codecs, select [DIF12](for the bottom slot), [DIF34] (middle), or [DIF56] (top)and press "Enter."

The reset operation takes 20 to 40 seconds to complete.

CDQPrima software version 28/6.28 and later, TA101, TA201 or TA301 :

1. From the CDQPrima's Front Panel, select [Common] using the arrow keys and press "Enter."
2. Select [TA Setup] and press "Enter."  
3. Select [DIFs] and press "Enter."  
4. Select [DIF12] for Digital Interfaces 1 & 2, [DIF34] for Interfaces 3 & 4, etc.,and press "Enter."  
5. Using the arrow keys, select [Reset] and press "Enter." 

The reset operation takes 20 to 40 seconds to complete.

[Back to TA101 Connection Problems]

 
Entering SPID Numbers

CDQPrima software version 27/6.27 and earlier, TA101 only:

1. From the CDQPrima's front fanel, select [Common] using the arrow keys and press "Enter." 
2. Select [TA Setup] and press "Enter."  
3. Select [DIFs] and press "Enter."  
4. Using the arrow keys, select [SPID] and press "Enter." 
5. Select [1] for DIF1, [2] for DIF 2, etc., and press "Enter."  
6. Using the number keypad, enter the SPID Service Profile ID # (provided by your local Telco.) and press "Enter."

CDQPrima software version 28/6.28 and later, TA101, TA201 and TA301:

1. From the CDQPrima's front fanel, select [Common] using the arrow keys and press "Enter." 
2. Select [TA Setup] and press "Enter."  
3. Select [DIFs] and press "Enter."
4. Select [DIF12], for Digital Interfaces 1 & 2, [DIF34], for Interfaces 3 & 4, etc. and press "Enter." 
5. Using the arrow keys, select [SPID] and press "Enter." 
6. Select [1] for DIF1, 2 for DIF 2, etc., and press "Enter."  
7. Using the number keypad, enter the SPID Service Profile ID # (provided by your local Telco.) and press "Enter."

[Back to TA101 Connection Problems]

 
Entering ID Numbers

CDQPrima software version 27/6.27 and earlier, TA101 only:

1. From the CDQPrima's front fanel, select [Common] using the arrow keys and press "Enter." 
2. Select [TA Setup] and press "Enter."  
3. Select [DIFs] and press "Enter."  
4. Using the arrow keys, select [ID] and press "Enter." 
5. Select [1] for DIF1, [2] for DIF 2, etc., and press "Enter."  
6. Using the number keypad, enter the ID # , for the TA101, the ID number is the last 4 digits of your 7 digit ISDN number, and press "Enter."

CDQPrima software version 28/6.28 and later, TA101, TA201 and TA301:

1. From the CDQPrima's front fanel, select [Common] using the arrow keys and press "Enter." 
2. Select [TA Setup] and press "Enter."  
3. Select [DIFs] and press "Enter."
4. Select [DIF12], for Digital Interfaces 1 & 2, [DIF34], for Interfaces 3 & 4, etc. and press "Enter." 
5. Using the arrow keys, select [ID] and press "Enter." 
6. Select [1] for DIF1, 2 for DIF 2, etc., and press "Enter."  
7. Using the number keypad, enter the ID # , for the TA101, the ID number is the last 4 digits of your 7 digit ISDN number. For the TA201 and TA301, the ID number is the 7 digit phone number (no area code).

[Back to TA101 Connection Problems]

 
Entering ISDN Switch Type

SwitchType Definitions, TA101
5E6 = AT&T 5ESS Custom Point-to-Point Software-Version 6 or earlier
5E8 = AT&T 5ESS Custom Point-to-Point Software-Version 8 or later
NTI = Northern Telecom DMS100
NI1 = National ISDN-1, Including AT&T

SwitchType Definitions, TA201 and TA301
5ESS Cust = AT&T 5ESS Custom Point-to-Point or Point-to-Multipoint, all versions
NI1 = National ISDN-1, Including AT&T

CDQPrima software version 27/6.27 and earlier, TA101 only:

1. From the CDQPrima's Front Panel, Select [Common] using the arrow keys and press "Enter." 
2. Select [TA Setup] and press "Enter."  
3. Select [DIF12] (TA located in the bottom interface slot of the Prima), [DIF34] (middle slot), or [DIF56] (top slot)and press "Enter." 
4. Select [Sw Type] and press "Enter." 
5. Using the arrow keys, select the appropriate ISDN Switch Type and press "Enter."

CDQPrima software version 28/6.28 and later, TA101, TA201 and TA301:

1. From the CDQPrima's Front Panel, Select [Common] using the arrow keys and press "Enter." 
2. Select [TA Setup] and press "Enter." 
3. Select [DIFs] and press "Enter."  
4. Select [DIF12] (TA located in the bottom interface slot of the Prima), [DIF34] (middle slot), or [DIF56] (top slot)and press "Enter."
5. For TA201 and TA301m select [N. America] and press "Enter." 
6. Select [Sw Type] and press "Enter." 
7. Using the arrow keys, select the appropriate ISDN Switch Type and press "Enter."

[Back to TA101 Connection Problems]

 
Defining Digital Interfaces

1. From the CDQPrima's Front Panel, Select [Common] using the arrow keys and press "Enter." 
2. Select [Dig I/F] and press "Enter." 
3. Using the arrow keys, select [Def I/F] (Define Interface) and press "Enter." 
4. Select [1] for DIF1, 2 for DIF 2, etc., and press "Enter." 
5. Using the arrow keys, select the appropriate Interface Type and press "Enter."

Interface Types:
[X.21]* = DIF101 configured for X.21 operation
[RS422] = DIF101 configured for RS422 operation
[V.35]* = DIF102
[TA101] = Internal TA101
[TA201] = Internal TA201
[TA301] = Internal TA301(Includes internal NT1)
* The [X.21XTA] and [V.35XTA] selections are for use with an external terminal adaptors.

[Back to Prima Error Messages]

 
Checking the NT-1, TA101 and TA201,

The following refers to the ATI UT620F and INCCM-NT1 NT-1's. For other brands and models, refer to the manufacturers unstructions.

1. Only the "POWER" LED should be illuminated on the NT1. 
2. If the red LED (S/T&U) is blinking rapidly (8 times/sec.), the U interface side(ISDN Line) has a problem. 
3. If the red LED (S/T&U) is blinking slowly (1 times/sec.), the S/T interface side(TA101) has a problem.  
4. If the red LED (S/T&U) is not illuminated, then the NT1 is functioning properly.

Checking the NT-1, TA301

1. Looking directly into the TA301 from the rear of the Prima, the green LED should be illuminated and the yellow LED should notbe illuminated. Any other condition is an error. 

[Back to TA101 Connection Problems]